Thursday, December 12, 2013

Golden Snitch Tree Ornament Tutorial

I have a new video up, a golden snitch christmas tree ornament tutorial! 

Here's the picture of the "real" golden snitch: 

(photo above is from here)

Here's my pattern for the wing. Please note that this was designed for a small ornament, so depending on the size of your ornament you may need to make this bigger. The image below is the actual size (8.5 x 11) So make sure to print it at full size to get the wings right.

There are quite a few versions now, but I think the original idea for the golden snitch ornament originated here

Thursday, September 26, 2013

Beaded Wire Wrap Bracelet

Just posted a new video, a tutorial for making a beaded wire wrap bracelet. I had some wire and beads lying around and I was trying to think of a simple way to create something using only the wire and beads, and this bracelet is the result. After I made it, I realized it is kinda like a wire version of the Chan Luu inspired wrap bracelets that are so popular. This was not my intention when I made it though, it just ended up that way. Serendipity, I guess! This project is pretty simple and quick to make, I hope you enjoy it! :)

Here are the written instructions from the video:

You will need:  Size 8 beads, 20 gauge wire, 28 gauge wire, needle nose pliers, a tape measure, and wire cutters.

Step 1: Measure your wrist loosely, then add an inch and a half (3.81 cm) to the measurement. (For larger wrists, add at least 2 inches (5.08 cm) to be safe – it’s better to have extra wire than not enough). Write this measurement down.

Step 2: Double the amount from Step 1, then measure and cut this amount of the 20 gauge wire.

Step 3: Carefully bend the 20 gauge wire in half. Make sure the bent end is rounded.

Step 4: Take the amount from Step 1, and multiply it by 4.5 inches (or 11.43 cm). Then, measure and cut this amount of 28 gauge wire.

Step 5: Take the end of the 28 gauge wire, and tightly wrap it three times around the 20 gauge wire, right below the loop end.

Step 6: Slide 3 beads onto the 28 gauge wire.

Step 7: Tightly wrap the 28g wire twice around the 20g wire, on the opposite side, just under the loop. Make sure to keep the beads as snug with the wire as possible.

Step 8: Slide 3 beads onto the 28g wire, and wrap it twice onto the opposite side of the 20g wire.

Step 9: Repeat this process, until the bracelet is the length of your measurement from step 1.

Step 10: Carefully bend the bracelet into an oval, then try it on your wrist. If it is not comfortable, keep adjusting the shape until it is. If it’s not long enough, add more beads.

Step 11: Once this is done, wrap the 28g around the 20g three times, then cut the 28g. Use the pliers to flatten it so there isn’t a sharp end sticking out.

Step 12: Cut the 20g wire, leaving some extra on both sides. Use the pliers to create a hook on each side with the extra wire.

Step 13: Test it by putting the hooks through the loop at the other end of the bracelet. When everything works smoothly, you’re done! 

Wednesday, September 25, 2013

First Post! Welcome :)

This is my first ever post on this blog! I have been wanting to start a blog for a couple years, and now I'm finally doing it! I have a Youtube channel, called Pugdemonium, and sometimes I buy/find/make things that I would like to share, but I think they might not be a good fit for my youtube audience and/or isn't really enough to make a video about. From now on, I will post those type of things here! I will also post any videos I upload here as well. To everyone reading, Welcome to my blog!! I am excited to begin this journey :)